You may have an internal problem if your water cooler doesn’t work properly. In such a case, you may want to check the refrigerant level, check the condenser fan, and check the circuit breaker. If none of these methods fail, you should call a professional technician.
Troubleshooting a water cooler
There are several things you can do to fix a water cooler that isn’t displacing water. The first thing you can do is to check the power source. If the power source is good, the cooler should be able turn on. If not, you can also try to adjust the thermostat.
Another simple troubleshooting step is to drain the water and turn off the power. This will tell you if the water has become too cold or frozen. A reset can also be performed by unplugging the back end switches and turning them off. If the water cooler isn’t dispensing water, you can reset it to see if the problem persists.
If that fails, you can call a plumber to get help. They will be able to examine the issue and get it fixed quickly. Most often, the issue is an airlock. This is when air pressure is forced into a unit when it is empty. To troubleshoot this issue, try holding down both taps for a few minutes. The water will return to normal once the air has escaped.
In some cases, the water cooler’s compressor may be malfunctioning. If the compressor isn’t working properly, the water cooler won’t be able to remove heat. It could also be due to a blocked drain or a bad connection. In either case, check the coils for corrosion or debris.
Another common issue is that the water bottle has run out. If the water in the bottle is empty, the water cooler might be leaking. If the water cooler is leaking, make sure it is plugged into mains power. If it’s the latter, shut off all switches before opening the housing.
Refrigerant levels should be checked
When a cooler stops working, the refrigerant level should be checked first. Low refrigerant levels could cause the home’s air to become warmer than normal. This could be due to clogged filters, or a compressor problem. You can also get it from improper thermostat settings. Thankfully, there are simple ways to check this yourself.
A window air conditioner that has low refrigerant may not cool as well as it should. This happens because the refrigerant doesn’t travel as far. The best way to check the refrigerant level of a window conditioner is to measure the temperature of the midlevel output airflow. You can do this with a digital thermometer. The thermometer can be placed near the air handler for a few minutes to allow the device to read the temperature.
Another common reason why an air conditioner’s refrigerant level is low is a leak. Leaks should not be a problem if the air conditioner is properly sealed. If there are any leaks, it is better to fix them than to add more refrigerant. Adding more refrigerant can cause more problems and could waste a lot of money.
A malfunctioning compressor could also cause your cooler to not cool your home as it should. This does not mean that the HVAC unit is not functioning; rather, it could be that the compressor is not starting or that the oil level is low. Low refrigerant levels could also indicate a blown fuse, a pressure control switch or a damaged circuit wire in the dash controller module.
Low refrigerant can also cause the coil to freeze. While scraping off ice on the coil may fix the problem temporarily, it’s best to hire an HVAC technician who can seal the leak and add more refrigerant. Low refrigerant levels can cause additional stress to your air conditioning system, particularly the compressor. Additionally, it may increase your electrical bill.
Checking the condenser fan
If you think your air conditioner or cooler is not working, the first step you should take is checking the condenser fan. If the fan is not spinning, there may be a problem with the fan motor. If this is the case, you may need to replace the motor or check the fuses. If neither of these steps work, you might need to consult a professional.
A broken contactor can cause the fan to stop turning on often. Sometimes debris can get stuck in the contactor, preventing it from turning on. Turn off the power and inspect the fan motor shaft for debris.
Your air conditioner’s fan will spin at 1725 RPM. Your compressor could burn out if it spins too fast. To determine if the fan capacitor is defective, you can also check it. If the capacitor is defective, it will leak fluid or rust.
The condenser fan is a vital part of the refrigerator’s refrigeration cycle. The fan is responsible for forcing air through the condenser coil, transferring heat from the compressor to the ambient air. When the fan isn’t working, the cabinet temperature can rise. Without the fan, the compressor will overheat and eventually fail.
The next step is to check your air handler unit if the condenser fan stops working. The HVAC system is usually indicated by a flashing light. The system is operating normally if the flashing light remains steady. If the light starts to flash in a pattern, a problem is present.
The first step is to test the power. If the fan is working properly, turn it on and check for short circuits in your capacitor. Afterward, test the resistance of the motor by conducting an ohm test on the fan’s windings.
Checking the circuit breaker
Check the circuit breaker if your cooler isn’t working. Many times, this breaker may trip without you even knowing it. To get the breaker working again, you’ll need to reset it. Checking the breaker is a simple process.
If the circuit breaker keeps trippling, it could be a short circuit. If the handle is not able to be pushed in to activate the breaker, it could indicate a fault in the circuit. This fault can be caused by damaged insulation in the hot and neutral wires. Insulation is made to protect the wiring from heat, but it can wear out and become damaged over time.
Also, make sure to check the compressor of your air conditioner. Your AC unit may heat up and run hot if it isn’t working properly. If this happens, the wire can produce a spike in amps and trip the circuit breaker. Amp spikes can also be sent to the breaker by hard starting the compressor, overloading it.
The circuit breaker can be dangerous to work in, so take care. Be sure to wear gloves and keep the floor dry. You can find the panel in your garage, utility room, or basement. The panel should have an index that shows which area of your home each circuit breaker serves.
After checking the fuse, reset the breaker, the cooling fan should be working. The problem could be more complex if it doesn’t. The problem may be more serious if there are frequent power surges. A qualified electrician can also be contacted to conduct a thorough diagnostic.
If you aren’t able to reset the breaker, you may need to replace the breaker. This is an easy but effective way of fixing the problem. The breaker could be defective or have loose wires. For those who aren’t comfortable doing this themselves, you can call in a professional to replace the breaker and tighten the wires.
Usually, it takes about 15 minutes for a refrigerator to cool before it trips the breaker. It can cause wires to heat up, and can also cause internal damage. Make sure the fan belt isn’t slipping. The fan will not run if the fan belt isn’t running.